فروردین 9, 1403 1:50 ب.ظ

ایران سرویس

خیابان بهبودی، نرسیده به نصرت، جنب بانک سپه، پلاک 145،ساختمان بنیامین،طبقه 5 واحد 18
دفتر مرکزی: 66097851  مرکز تعمیرات: 66097859  شعبه شرق: 77978135  شعبه هفت تیر: 88836102  شعبه جنوب: 55300568   شعبه غرب: 44153186   شعبه شمال 26721443   شعبه اسلامشهر و رباط کریم: 56746602

 پیاده سازی Lumix GX80/85 پاناسونیک
پیاده سازی Lumix GX80/85 پاناسونیک

مرحله 1 پیاده سازی لومیکس پاناسونیک

  • ذرات گرد و غبار زیر شیشه سنسور وجود دارند، بنابراین پیچاندن سنسور به دفع آنها کمک نمی کند.
  • اگر دوربین را در حالت “A” در f / 22 قرار دهید و از آسمان عکس بگیرید، می توانید گرد و غبار را به بهترین شکل تشخیص دهید.

I have dust particles underneath the sensor glass, so sensor swabs didn't  help me. I will try to get inside and under the glass. Additionally the EVF is overbright after a drop and maybe can be rearranged in the process.You can spot the dust best if you set the camera to the "A" mode at f/22 and take a picture of the skyYou can spot the dust best if you set the camera to the "A" mode at f/22 and take a picture of the sky

مرحله 2

  • دو پیچ دارای طول های مختلف را بردارید.

Start with these two screws. Remember screw sizes and position, there are many different lengths used!

مرحله 3

  • فنر فلش و 4 پیچ را بردارید.

remove the flash spring as shown and the four screwsremove the flash spring as shown and the four screwsremove the flash spring as shown and the four screws

مرحله 4

  • این پیچ را بردارید.

Remove this screw

مرحله 5

  • به این قسمت (در تصویر مقابل) دقت کنید.

Insert wisdom here.

مرحله 6

  • صفحه پشت و سپس کابل های نواری را بردارید.

remove the backplate and remove the ribbon cablesremove the backplate and remove the ribbon cables

مرحله 7

  • 3 پیچ را بردارید.

remove the 3 screws

مرحله 8

  • برای برداشتن راحت سنسور، ابتدا میله بالا را بردارید.

to remove the sensor more easily you can remove the top bar beforeto remove the sensor more easily you can remove the top bar beforeto remove the sensor more easily you can remove the top bar before

مرحله 9

  • خازن E فلش را بردارید.

Flash E.Capacitor removal

مرحله 10

  • 3 پیچ را برداشته تا گلس کاور سنسور خارج شود. دقت کنید که آنها داخل محفظه خود سقوط نکنند. مغناطیس های قوی در آنجا وجود دارند.

اکنون پیاده سازی دوربین لومیکس پاناسونیک شما به پایان رسیده است!

Remove the 3 screws to get the sensor cover glass off. Be Careful not to let them fall inside the housing. There are extremely strong magnets!Remove the 3 screws to get the sensor cover glass off. Be Careful not to let them fall inside the housing. There are extremely strong magnets!

مرتبط با دوربین پاناسونیک: پیاده سازی DMC-FZ1000 Lumix پاناسونیک

اطلاعات بیشتر درمورد محصول 

بخوانید  تعمیر سیم شارژ VTech CS6719-2

پاسخ دهید

نشانی ایمیل شما منتشر نخواهد شد. بخش‌های موردنیاز علامت‌گذاری شده‌اند *